30
Nov
Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case. As the bobbin starts filling up with thread move your finger from side to side so that it fills up evenly.
Slide your bobbin into the bobbin case and guide the thread through the slit on the case and bobbin finger if your driver has one.
How to install a bobbin. How to install the bobbin. Follow these steps in install the bobbin wound with thread. Turn the sewing machine off.
Make sure you turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew you could be injured. Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case.
Only use bobbins that were designed to be used with this machine. Make sure you set the bobbin so the thread unrolls in the right direction. Holding the bobbin case lever open insert the bobbin case into the cavity under the presser foot.
Align the metal arm on the bobbin case so that it sits. In case of a machine equipped with Quick-set bobbin needle plate with a cutter for bobbin thread lightly hold down a bobbin with your finger and cut the thread with the cutter when installing a bobbin into a bobbin case so that the thread can be inserted through the tension-adjusting spring surely. Heres how to put a threaded bobbin in your sewing machine.
This process can be broken down into 3 main stages. Insert the bobbin into your sewing machine. Thread the upper thread system and needle.
Pull the bobbin thread up. There are about 2 ways to insert the bobbin and 2 ways to pull the bobbin thread up or not. Lift the lever on the bobbin case and remove it from the sewing machine.
Leave a tail of about 3 to 4 inches of thread and place the bobbin in the bobbin case. There is a certain way the bobbin must be set in its case. In addition there will be at least a couple of slots in the bobbin case youll need to draw the thread through.
Slip the bobbin case onto the spool inside the compartment. Release the lever on the bobbin case so it is snug against the case. The lever will automatically lock into position if it is in the correct position.
How to thread and install the bobbin case in a front loading singer sewing machine. Singer sewing machine parts schematics list note. Singer featherweight 221 222 repair.
Apr 14 2013 the bobbin case of my singer 5932 broke bought a replacement but i can t seem to get in installed correctly. This is a very important step as the bobbin can become. To install the bobbin press the presser footneedle exchange key raise the needle and raise the presser foot lever.
Remove the bobbin cover and insert the bobbin into the bobbin case make sure that the bobbin thread unwinds to the left. For a new bobbin case part code. XC3153-251 green marking on the screw XC8167-451 no color on the screw contact your nearest authorized dealer or service center.
If the needle plate has been removed it is especially important to reinstall the needle plate and tighten the screws prior to installing the bobbin case. I purchased some bobbins for my Trident 660 successfully installed the left side by removing the torx screw. The right side bobbin threading is covered.
I cannot for the life of me remove this cover. Ive tried razor blades flathead screwdrivers anything flat to wedge and remove. Slide your bobbin into the bobbin case and guide the thread through the slit on the case and bobbin finger if your driver has one.
Check that the tension is properly set by pulling gently on the loose thread. Make sure you can pull a few inches of the thread otherwise the tension might be a bit on the high side. Step 5- Install the Bobbin Case.
Hold the bobbin case in your left hand insert the loaded bobbin into the case with your right hand. Make sure the thread is set to spin out from the bobbin in a clockwise direction. Pull the end of the thread through the slit in the bobbin case and then direct the end of the thread under the hook on the case.
Inserting the bobbin in a Kenmore Sewing Machine like the 158 Model series requires a certain amount of precision but following the steps in order will simplify the process. The 158 is a free-arm model so the accessory box will need to be removed by lifting up on the front end of the machines arm before a bobbin can be inserted. The bobbin case tension can be adjusted with a set screw but its easy to strip the tiny screws threads.
On an older Husqvarna machine with a vertical bobbin case it was easier to test. The bobbin case with the bobbin in place dangled from the thread when held by the thread outside of the machine. Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case.
Only use bobbins that were designed to be used with this machine. Make sure you set the bobbin so the thread unrolls in the right direction. Its difficult to explain how to do this in words so Ive made a video that explains exactly how to make sure that youve got your bobbin case holder correctly inserted.
Click here to watch the video. I hope this helps you if youve been having problems with getting the bobbin case holder properly installed in your Janome sewing machine. As the bobbin starts filling up with thread move your finger from side to side so that it fills up evenly.
Once you have enough thread on the bobbin simply snip it off and remove the bobbin from the spindle. Placing or installing the full bobbin in a mini sewing machine. It is now time to install the bobbin inside your mini sewing machine.