How to install bearing race

Clean beneath the area where the race installs. An investment in proper tools training and time will result in cost savings and prolonged bearing and machine life.

If playback doesnt begin shortly try restarting your device.

How to install bearing race. Cheap Easy Way to Install Bearing Races. Cheap Easy Way to Install Bearing Races. If playback doesnt begin shortly try restarting your device.

Videos you watch may be added to the. How to install wheel bearing race without socket or press. If playback doesnt begin shortly try restarting your device.

Videos you watch may be added to the TVs watch history. Find a socket that is just slightly smaller than the outer diameter of the bearing race but is large enough to make solid contact with the lip of the race. Place the new race over the hub where it will be installed.

Make sure the socket can fit into the hole that the race is going to be installed in. Place the socket on the end of the race. Bearing race installation - YouTube.

How do you install a bearing race without a press. One alternative method to pressing in a bearing race is to use a socket to tap it into place. Remove the old bearing race according to the workshop manual for the car.

Clean beneath the area where the race installs. Never heat bearings above 250F 129C. Electric ovens and electrically heated oil baths are commonly used.

Protect the bearings from the heat source with a simple wire screen holder or ceramic plate. Place the heated inner race solid against the cold shoulder on the shaft until the inner race grabs on to the shaft. The heated inner race will pull away from the cold.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Mount the arbor press to a working table and use the handle for leverage by applying pressure one step at the time. By doing this youll lover the rack and unmount the bearing.

Dont add a pipe or any other holding element to the handle as you may damage the press and the bearing. Bearing installation and removal basics. An investment in proper tools training and time will result in cost savings and prolonged bearing and machine life.

Tap it in to start square and work around the race with the driver in line with the edge of the race. Place the driver where it needs to be to keep the race square with the bore. If it gets crooked go the the other side to straighten it out.

Driving it in to straighten it can damage the bore and make it out of round. The outer race or cup is the bearings exterior ring. Since it protects the bearings internal parts it must be machined smoothly and accurately.

The inner race or cone is the part of the bearing that sits directly on the shaft. It is important that the race is started straight and driven in with an aluminum press plug. Strike the driver handle with a heavy hammer.

You will know that the race is seated when the striking audible changes from hollow to solid. Bearing races should be replaced every time bearing replacement is necessary. To learn how to install a bearing race you will need a bearing race and seal driver.

This set is used to lodge races into the hub assemblies using the various size steel discs and displacement shaft in the box. Pick up a new bearing place it in the hub and hammer it into place using the appropriate size disc for alignment. Hot oil pots with a tray or hook to support the bearing cone inner race effectively ease the installation of tight inner races on shafts.

Place the heated inner race solid against the cold shoulder on the shaft until the inner race grabs on to the shaft. The heated inner race will pull away from the cold shoulder unless held in position. Im showing how to change out a bearing and a race from the hub.

When banging out the race make sure a softer metal is used on banging out the. In this video you learn how to replace wheel bearing races. You will need a wheel bearing race installer kit.

Hammer and a chisel. Visit our mechanic store a. We offer a tool for installing bearings races and seals kit PTW83020 from Performance Tool.

This is intended for installing these items but it could also work to get them out of your hubs. Sometimes mechanics will use a socket or piece of pipe sizes to the hub bore for removing old races bearings and seals. Please refer to the linked video.

Make sure you replace the wheel bearing races before you resurface the rotor. Lay the rotor on a piece of wood. Using your chisel chisel out the race by hitting the lip of it.

Flip over the rotor and set the new race in place. Take a race installer that fits the race and hammer in the new race. Make sure it drives in evenly.

To install your races this is what youll want to do according to our help article on replacing bearings races and seals on a trailer hub which Ill link for you. First place the race in the hub thin edge towards the outside. Carefully tap in the race until it is level with the hub.