How to put bearings in wheels

Then get the other bearing and place it in the hole of the topside of the wheel. If the bearings go in very tightly use a metal washer min.

5 extra or old bearings.

How to put bearings in wheels. To View the Next Video in this Series Click Here. How To Put Bearings in Skateboard Wheels - YouTube. A quick video showing you how to put bearings into skateboard wheelsFollow us.

First try on a new or cleaned wheel bearing. Most bearings are painted on one side. It is recommended that the bearings be placed with the colored side out although it is not so important.

Then gently pressing the outer metal ring of the bearing lower it into the hole in the bearing. Then you take the wheel put that on top of that and you take your other bearing again with the flat face out apply it to the top of the press here fix it in skew it back and then once you have got the bearing set up like this all you do is just use your hand to press forward and this machine will actually do it in a nice fluid motion for you. Put the caliper and brake pads back in place and secure them with the appropriate bolts.

Finally put the tire back in place and secure it with lug nuts. When youre all done carefully lower the car back down to the ground with your jack. Congratulations - youve just changed your wheel bearings.

How to Rebuild and Repair a Wheel Bearing on a Bicycle - YouTube. Add the Bearing spacer if you have such. And be sure its the correct size as there-are 10mm and 8mm widths.

Then take said wheel needing bearings and Slam it onto the Bearing. Then spin it freely just to check you didnt FU this simple thang. If it spins pretty well then pull the wheel off with the bearing.

With the first bearing mostly seated flip the wheel over and align the other bearing into the back of the wheel. Press down to seat the second bearing. Both bearings should now be on the skateboard truck axle.

Take the other speed ring and put it on the axle. Finger tighten on the axle nut. Using a ½ socket tighten the axle nut.

Some little clicks might be heard while doing this. This is the sound of the bearing seating into the wheel. No if you tighten them all the way down the spacer should only be touching the inner race of the bearing which in fact will not allow the two inner bearing races two move but the balls and the outer race will still glide allowing less friction and play for a more precise roll.

Start with the inside bearing stick axle rod halfway and push it side to side to pull the bearing out. Repeat this process for all the bearings. Install new bearings in the skate wheels.

Now place the new bearing in the axle of the skate and press down with the wheel onto it. Press it firmly until the bearing is seated properly in the wheels. Do the same thing for other side and repeat the process for all the wheels.

Seat bearing in the wheel. Put one skateboard wheel on top of the bearing. Press the wheel towards the bearing till it comes into place.

Then get the other bearing and place it in the hole of the topside of the wheel. Again press the bearing into the wheel using your palm. Check the wheels and the bearings and adjust till they are in the proper place.

How to install your bearings. Press the bearings evenly into the core of the wheel using an axle bolt and 5 extraold bearings. This way damage to the bearings is minimal.

If the bearings go in very tightly use a metal washer min. Diameter 22mm on both sides of the bearings. Get an aluminum hanger and use its side to press the bearing within the wheel.

However check the bearings first for shields. If the shield is only on one side then put that side down on the axis. Put one wheel ensuring its core is on the top of the bearing.

Use the palm of your hand in pressing the bearings into place. With new bearings and wheels you may need to more forceful in installing them but that is. Place your wheel on the axle on top of the bearing.

Press down with your hand work the pressure around your wheel and push down hard. Step 4 Place the 2nd Bearing. Take your wheel off and pop it to one side.

Place the 2nd bearing on the trucks axel along with a spacer. Step 5 Pop the wheel. Grab a wheel and one of the bearings and try to push the bearing into the wheel.

If the bearing has one metal side and one plastic side - the dust guard - you should have the plastic side facing outward and the metal side on the inside when you insert it. Some bearings have metal on both sides so either way is acceptable. Press-in bearings provide a preset assembly that comes greased and sealed.

The internal clearances are set so you dont need to adjust the bearing. After removing the steering knuckle from the vehicle remove the bearing retaining snap ring. Press the hub stud out of the bearing using the appropriate tooling to prevent damage to the knuckle.

Axle bolt with screw. 5 extra or old bearings. How to instal your bearings.

Press the bearings evenly into the core of the wheel using an axle bolt and 5 extraold bearings. This way damage to the bearings is minimal. If the bearings go in very tightly use a metal washer min.

Diameter 22mm on both sides of the bearings.