How to run a seadoo out of water

Its perfectly fine to do that. I usually run mine for a least a minute on the hose when flushing out salt water to make sure it get a good flush.

In the future when you get the ski out of the water start it and run it for 5 seconds at no more then 4000 rpms you will see water evacuate the exhaust system.

How to run a seadoo out of water. You can run it for about 2 minutes out of water on the hose this is because the pump seal does not have any cooling when the water craft is not on the water. I usually run mine for a least a minute on the hose when flushing out salt water to make sure it get a good flush. Never run the motor of your watercraft out of the water.

While your Sea-Doos ROTAX engine features a closed-loop cooling system similar to that found in an automobile to ensure a consistent debris-free source of cooling liquid that liquid is cooled as its passed through internal channels in the crafts ride plate the rectangular metal. You can run a Sea-Doo out of the water while its attached to supplying water. Be careful as unlike other manufacturers Sea-Doo recommends that you never run the engine without supplying water.

But even if its flushed with running water a Sea-Doo can be run for no longer than 2 minutes out of the water. Running a sea-doo out of water. Yes but you do know to start engine first then turn on water.

NEVER HAVE THE WATER RUNNING WITHOUT THE ENGINE RUNNING OR YOU WILL FLOOD THE ENGINE WITH WATER. It is ok to run the engine without water for 15-30 seconds or so. If the engine stops turn the water off as soon as possible.

A water hose has pressure and if the engine is off the water will find its way into the cylinders and hydro lock your engine. So its essential that you have the engine on before turning on the water. Then turn the water off before turning the engine off.

Continue running the engine for four to five minutes. This will flush all of the salt water out of the engine. Turn the water off.

Continue running the engine for a few more seconds until no more water expels out the back. Turn off the Sea-Doos engine and remove the garden hose from the water injection port. However most can be flushed using a traditional water hose.

First press the ignition button and let the engine run for a few seconds never more than 15 seconds as it can cause damage. However you should have just enough time to quickly turn on the tap and let a strong flow of water enter your machine. You can run her dry for up to about a minute any longer than that hook it up to a water hose even on the hose no longer than three minutes even through you are cooling the engine and exaust the carbon seal on the drive shaft through hull is not being cooled.

1997 seadoo GtS and how to run it out of water test. If playback doesnt begin shortly try restarting your device. Videos you watch may be added to the TVs watch history and influence TV.

So the manual say run for 2 minutes max why there is not water flowing over the aluminium plate to cool it down so engine will over heat quick. Then could melt the plastic hull not good. Second open loop that comes from the pump to the exhaust manifold to cool the exhaust gasses and flows to the muffler and out this couldnt be cooled by the closed loop as too much.

To run your boat motor out of water start by attaching a hose to your motors water intake so you can flush in water which will avoid damaging the engine. Once the hose is attached turn on the water faucet. Then pull the gear shift to neutral and start the engine.

You need to get a flush kit that will fit your Seadoo. The kit will allow you to run your engine when the vessel is out of the water. I have a 2000 Challenger seadoo jet boat with the Mercury 240 hp efi motor.

Last 2 times out on the water the engine will not respond to the throttle. It wont go past 15 mph. At 2000 rpm it runs perf.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Cleaned carb replaced fuel lines in tank. Breathed new life into this original PWC.

You can put in a simple T connector in the coolant line going to the en. You can run it about 30 seconds or so without any hose. Its perfectly fine to do that.

It wont overheat or anything. But since the hose was on when the motor died you def want to start it up give a couple blips to the throttle and run it dry for at least 30 seconds. Rev it up real good.

It will blow any water out. Running jet ski out of the water. Old rule of thumb 15 15.

Run it for 15 seconds. Let it cool for 15 minutes. Kerker pipe OP ride plate.

1989 JS 440 Hull. 1990 X2 650 the new kid on the block. 1992 Kawi Sport Cruiser 650 The Build.

How do you start a Seadoo out of water. Start the motor and then run it until blue water comes out of the exhaust 15 seconds then turn off the mixer and then the motor. Wait for a couple of minutes and then turn the dial to Flush on the Salt-A-Way mixer and then run the ski for another 30 seconds or so until clear water comes out.

In the future when you get the ski out of the water start it and run it for 5 seconds at no more then 4000 rpms you will see water evacuate the exhaust system. For the winter if you have an air compressor blow it out you will hear some gurgling air coming out of the exhaust and a few ounces of water evacuate. A Seadoo doesnt use lake or ocean water to cool it down but instead uses antifreeze just like your car does.

But this does not mean you can run a Seadoo out of water or on a trailer for very long. This is because the exhaust system uses lake water to keep it cool and when its not in water it starts to overheat. 15 Sea-doo Spark 900 ACE Stock.

It with fresh oil and you will have to do a boil out procedure where you get the engine temp up high enough to boil the water out of the oil you cant keep running the engine with any water in it it isnt a lubricant and will cause bearing failure if you dont. There is a specific. Repeat the above process until the engine stays running.

You may have to repeat the process several times. After the engine is running it needs to be run for an extended period to bring it up to operation temperature for at least 20 minutes. The longer the better as running the engine will remove the last remnants of water from the engine.

There is a built in bilge pump which removes water whilst the motor is running. Then when you load the ski onto the trailer the remaining water drains out of the hull through the removable drain plug. If you check out the hull diagram on the Seadoo Warehouse site youll see it there.

1 - 5 of 5 Posts.