24
Jul
Just like wax you are going to wax on wax off. You dont want to put too much compound on the car that may dry up before you can get to it so working a large section is not a good idea.
Just like blood and eggs.
How to use rubbing compound with a buffer. If applying the rubbing compound by hand then put a small amount onto your cloth or applicator and begin to rub the affected area with a gentle circular motion. If the area to be treated is large you are advised to start at the top and work down. Applying Rubbing Compound Using Orbital Buffer.
Unlike the hand method that allows the user to move in a clockwise direction the orbital buffer methods allow the person applying rubbing compound to move in one direction. However it produces better and more efficient results than the manual method. Try and find something less aggressive to follow up the Rubbing Compound though.
See if you can find Meguiars Polishing Compound as that as designed to follow Rubbing Comopund. Try and use the Polishing Compound or the less aggressive product with a foam applicator as it will finish out much nicer and leave a glossier finish. Well the reason is pretty obvious.
Rubbing compound polishes the paintwork by literally eating away the paint material. Once the compound has done its work you will notice that all those ugly scratches will simply vanish. You can use the rubbing compound to polish the existing paint work or remove all kinds of paint scratches from the work.
Apply polishing compound sparingly to the face of a revolving buffing wheel. Repeat application of compound as needed during the buffing and polishing operations. Use only slight pressure in applying the revolving buff to the work surface thereby allowing the buffing wheel and the polishing compound to do the work.
Use only slight pressure in applying the revolving buff to the work surface thereby allowing the buffing wheel and the polishing compound to do the work. If after polishing the work surface is still dull it will be necessary to repeat the operation following up with a finer suitable compound. Wipe on a little area work it in and then wipe clean.
In the future tape off the plastic areas or pre-treat them with the Vinylex if you expect to splatter. The Tide was only used this once to prep for the buffing and for the waxing. Most of the rubbing compounds contain water and this is fine for re-wetting.
Rubbing compound is just a grit with a vehicle oil wax water to carry it to the work. Jewelers rouge for example is a very fine grit sanding agent with wax as its agent. There was another thread here about the green paste sold somewhere.
Immediately after apply some rubbing compound on a cloth and rub the gelcoat in a circular motion until the surface is shiny. Immediately remove all traces of compound with the clean microfiber cloth to avoid excessiveuneven abrasion of the gelcoat. Your boat is ready to be waxed.
A heavy-grit buffing compound You can use a heavy-grit buffing compound to remove stains and corrosion from the most damaged areas of your gelcoat. A medium-grit buffing compound A medium-grit buffing compound will usually be ideal for most of your boats gel-coat and should also be used on areas where youve used a heavier-grit. Make sure to apply the product on a cool clean surfac e and out of direct sunlight.
Apply the compound onto a damp applicator pad or a cotton towel over a small area at a time. Rub the product into the surface using back and forth motio n. When you apply the compound first and then start to polish later the piece that you need to polish will actually help you work the compound deeper into the buffing wheel while it is polishing which will give you far better and faster results while conserving your compound.
If you use more compound at a time you will actually decrease the. Rubbing compounds should work just fine. Use a medium cut rubbing compound and if you want go over that with a swirl mark remover.
Use a soft cloth and some elbow grease with the rubbing compound and less elbow grease with the swirl mark remover. You can of course use a buffer as well but be. I know it sounds crazy but try some peanut butter.
I have a friend in the paint business that showed me this little trick. Its the vegetable oil in the peanut butter that works. Then just use vegetable oil because the protein in peanut butter can cause stains.
Just like blood and eggs. How To Buff Clear Coat Like Glass - How To Use Compound - How To Get Mirror Finish - YouTube. Rubbing compound can be applied by hand using a microfiber towel and a ton of elbow grease.
Just like wax you are going to wax on wax off. Applying a pretty good amount of pressure in a circular motion apply some compound to your towel and buff it in using a clockwise rotational movement. Work the buffer using moderate downward pressure in an up and down or side to side direction covering your last pass by about 50 percent working one defined section of the car at a time till the compound is gone.
You dont want to put too much compound on the car that may dry up before you can get to it so working a large section is not a good idea. Rinse all of the soap residue or glass cleaner with water and dry the window before applying the rubbing compound to the scratch. Place the rubbing compound into the scratch–the compound should look like toothpaste and be easy to apply.
How does toothpaste remove scratches from windshield. Apply a dollop of toothpaste to a soft cloth and rub it into the scratch using a circular motion. See how a few minutes work with a buffing pad and rubbing compound gets rid of some very ugly scratches that happened in a parking lotREAD MY POPULAR ARTICL.
Fix a wool pad in the middle of the orbital polisher. Use a thin layer of rubbing compound which is made in a squeeze tube for easy use directly on the painted surface of the scratches. If it is made in a can then you should use a paper towel to take a little compound and apply on the scratch.
Buffing compounds are used with buffing and polishing wheels to increase the effectiveness of the wheel and to help you accomplish your tasks more quickly. They come in all different types and colors each uniquely suited to a different aspect of the buffing cutting and polishing process. Some are rougher and allow you to quickly remove scratches.