How to use snatch block

If you have found a solid anchor point run a strong strap or chain around it and insert it through the holes of the blocks side plates. Pull the rope firmly into the pulley channel on the snatch block.

This involves running the winch cable through the snatch block to an anchor point that is off at an angle.

How to use snatch block. Fastening the Snatch Block. Keep on pulling until it reaches the broken or stuck vehicle. Afterward unlock your snatch block from the sides of the plate and connect the thread of the winch carefully.

Now your duty is to lock the snatch block and check if its fully attached or not. To use a snatch block with an attached chain and grab hook to maximize your towing strength do this. Park on a flat stable surface where the tow truck will not be interrupted.

Attach the chain and grab hook to a strong sturdy stable anchor point. This must be something other than the tow truck or the wrecked vehicle. To position the winch line properly inside the snatch block the top part is rotated fully exposing the interior pulley.

Once that is the case the top part of the loop is rotated over the other half. Now with a D-ring the non-pulley part of the snatch block can be attached to the mounting point. Steven Walker demonstrates how to properly use a snatch block and load cell when conducting a liftLearn more about The Crosby Groups on-site safe rigging c.

Arguably the most useful use of the snatch block is using a recovery technique called a double line pull. This is when you run your winch cable from your stuck vehicle out to a suitable anchor point. You then feed your line through the snatch block and run it back to a recovery point on your 44.

The Process Using a snatch block greatly increases the pulling power of a winch. When a winch drum is fully spooled with cable it has less power than if it is spooled all the way out due to less line being on the drum which changes the effective pull ratio. Snatch blocks allow you to change the direction of a winchs cable by off-setting the anchor point allowing you to pull in a three-point motion.

Sturdy and durable snatch blocks are ideal for transferring loads over short distances and are commonly used in recovery situations. Lower Block LBS Working Load Limit for Crosby Blocks indicates the maximum load that should be exerted on the block and its connecting fitting. A single sheave block used to change load line direction can be subjected to total loads greatly different from the weight being lifted or pulled.

When this isnt possible you can use a snatch block to set up an angled single-line pull. This involves running the winch cable through the snatch block to an anchor point that is off at an angle. Then you need to identify a second anchor point thats angled in the opposite direction as the first anchor point.

Pulling beetle kill ponderosa logs with a snatch block setup. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features. To use a winch snatch block run the main cable of the winch through the pulley.

If you have found a solid anchor point run a strong strap or chain around it and insert it through the holes of the blocks side plates. Make sure the block is really genuinely secured to the anchor point. How To Use a Snatch Block with a Winch - YouTube.

How to Use a Snatch Block. You can use a snatch block for two types of winch rigging. One is for an offset anchor point and another one is for double line pull.

I will discuss both of them briefly. Offset anchor point One of the basic rules for winching is to make sure that the cable rolls up on the winch drum evenly. To use a winch snatch block run the main cable of the winch through the pulley.

If you have found a solid anchor point run a strong strap or chain around it and insert it through the holes of the blocks side plates. Make sure the block is really really secured to the anchor point. In this video Braden shows you how to properly use a snatch block tree saver along with a 5000lbs black op series winch while out on the trailCheck out our.

When you are using a snatch block to gain a mechanical advantage or redirect the winch line use a shackle to connect the snatch block to the tree saver. Thread the winch line around the snatch block sheave before connecting it to the shackle. Only use rated shackles the manufacture lists the working load limit WLL of the shackle.

How do you use a snatch block for vehicle recovery. In self-recovery the cable is run through the snatch block then back to your vehicle. Connect the snatch block to an anchor point directly in front of the vehicle.

Pull the wire rope from the winch and thread it over the pulley in the snatch block toward the object you are pulling or lifting. Pull enough wire rope through the snatch block to reach the object and allow for the rigging you will use there. Lock the cable release lever.

Pull the rope firmly into the pulley channel on the snatch block. McKissick 420 Champion Snatch Blocks McKissick 420 Champion Snatch Blocks WR 34-78 19-22mm WLL 12t. McKissick 416 All Alloy Snatch Blocks McKissick 416 All Alloy Snatch Blocks WR 34-78 19-22mm WLL 7t.

Crosby C-720 Heavy Duty Utility Snatch Blocks Crosby C-720 Heavy Duty Utility Snatch Blocks. The first use of the snatch block is something you have probably observed more than once in your lifetime. Snatch blocks are added to a rigging set up in order to increase pulling power.

The more blocks in the setup the less power required to lift the load. However the downside is that more blocks require more rope or chain. In the case you have a snatch block you can increase your pulling power by attaching your winch to the snatch block attached to a tree and then back to the D-ring on your front bumper.

When your vehicle is stuck in the mud With a snatch block to a tree you can either winch yourself out with a single line or a dual-line pull.